renpen

The tractor has a 3 cylinder diesel engine with low hours. It will run fine for a while and than just die. Sometimes it will restart but not always. I have changed the fuel filter, cleaned the water separator and inspected all the fuel lines/fittings. The fuel in the tractor is fresh and looks clear when drained into a glass container. The injector pump solenoid "clicks" when the key is turned on and you can hear the electric fuel pump running with the key on. It is sitting with the bucket down and full of gravel and a chipper on the three point so taking to the shop is difficult. Any ideas/help would be appreciated. Thanks.

I have removed, taken apart and soaked the carb in a cleaning solvent. I rinsed it, blew it out with air, ran a copper wire through all the passages, blew it out again and the engine runs exactly the same. I checked the fuel pump, it is good, it has new fresh fuel. I put a new gasket between the carb and the engine. Compression is good. I am thinking that maybe the crankshaft seals are leaking. The engine has sat for a couple of years. Anyone have any ideas?

I have removed and cleaned the carburetor with no change in the way it runs. It will not idle and will not run without fiddling with the choke. I soaked the carburetor in a gallon of carb cleaning solvent, I blew it out with air and ran a fine wire through all the passages. Fuel pump is working fine. I am beginning to think that one of the crankshaft seals is leaking. Anyone have any ideas?

I am running windows 7 and using windows live mail client. When I receive an e-mail from overstock as an example the images don't show up. There are red x's in the corners and there is a banner across the top saying images were blocked. If I click the banner I get the images. What setting am I missing?

I have windows premium home addition. I can not open PPS. files in windows mail. In set associations it shows powerpoint viewer as the program. What am I missing? I continue to get an error message saying to set an association. I can save the attachment and it opens fine in documents.

I have a 98 Honda Accord that now has ignition switch problems. In 2002 Honda put out a recall on the switch. It was never done on this car. This is known because of the lack of a punch mark over the 8th digit of the VIN. My question is, do these recalls expire or are they good until they are performed?

I am looking for the part that goes between the carb and the intake, it also holds the reeds. I can't find a site that has parts new or used. This is an older saw, probably early 70"s. It is a model P-42.

Female singer, sounds like the same one in both commercials.

I have a motorola razr v3. I have looked at the motorola software, phone tools 4.0 and read the reviews. A large percent of the reviews are negative. Like most things there are always some that can't make it work but this seems to be a common theme. I don't have usb 2.0 so I have been told that the blue tooth is not an option. Does anyone know of better software than the motorola phone tools? I mainly want to transfer photos from my phone to the computer and am not interested in the calender features.

I am thinking about installing a detroit true trac in the rear of my toyota pickup. I have 35" tires and 5:29 gears. I would also like to know why there is a difference between the front and rear true trac. Most lockers are interchangeable. I have looked on the internet for information but can't find any tech sites on the subject. Any help?

I am replacing the floor in the kitchen and in front of the door to the outside is a soft spot probably caused by water and years of wear. I am thinking about an overlayment as sort of an entry pad rather than trying to replace the subfloor. I was thinking about marine grade plywood or is there something better? It will get the normal amount of water on it from the traffic through the entry door.

Has anyone had a mouse problem in their motor home? How do they get in and how was the problem taken care of?

The fan is part of the rotor and not sold seperately even if it would come apart. Any thoughts on the type of epoxy to use? It is a plastic material. The fins are intact, only the mounting points (2) failed.

The fan on my 5kw generac generator is broken and can only be replaced by replacing the rotor assembly. I am considering epoxy or taking the fan out all together. Would running without a fan be an issue under light loads for reativly short periods?

I have removed the stator and the rear bearing carrier but the rotor will not move. I have been letting it soak with WD-40, this is the second day.

I installed a daytime running light module. I found a wire that is hot in run only. The lights stay on while the engine is starting. I have noticed with factory installed units the lights go off during starting. Is there an easy way to identify a wire that would produce this effect on my 02 Mazda pickup? I would like the lights to go off during start.

I am installing vinyal floor tiles in the kitchen. I have self stick type tiles. My question is can I use tile adhesive with this type of tile and will it provide better adhesion.